Interior door decoration: additional elements and cashes

Door replacement is a serious event. With a good budget, there is nothing complicated here - I chose and ordered, accepted and paid. As a rule, the company does the work "on a turn-key basis." If it is necessary to save and install the doors yourself, then there is often a problem with their finishing. People far from such work may simply not know how to get out of some difficulties. Most often, when installing doors, the following problems arise: • A mismatch between the dimensions of the opening and the doors; • A discrepancy between the depth of the opening and the door unit; • • The wall surface does not match the vertical level. 1. In the case when the opening is narrower than the assembled door unit, the problem is solved by expanding it, this is the only way. But if the door is not included in height, then it is sometimes easier to cut off a little.It is necessary only to remember that many doors are empty inside, wooden bars are installed in them only around the perimeter. Therefore, sawing off more than 3-5 centimeters is not recommended. If the doorway is too wide and there is no possibility to reduce it, then this space can be filled with mounting foam. However, when the thickness of the foam layer is more than 5 cm, this design may be weak, not rigid. On the other hand, the foam is easily plastered. A layer of plaster in 2 cm has excellent reinforcing and strengthening properties.
 interior doors doors
 Interior doors
2. The depth of the opening is the thickness of the wall in which it is located. This parameter rarely coincides with the depth of the door unit, which has, as a rule, the standard value. It is this difficulty that is directly related to the finishing of the door and the opening. Questions may arise when installing doors. For example, which side of the wall should be flush with the door, and which side should stick out.In most cases, the side where the hinges stick out, that is, the opening side, is flush. But sometimes this rule can be neglected. In any case, a wall cut protruding from behind the door frame remains open. This is exactly the problem for an inexperienced installer. Additional elements. Under this name hides the means that increase the width (depth) of the door block and hide the very slit wall (their also called "dobory", "broadens", "slopes"). Due to this, both sides of the wall and the end faces of the risers become respectively coincident in the plane. Risers, by the way, are called the side parts of the door unit: there are loopback and locking risers.
interior clerks doors
 interior door cashes
When buying a door in a store, they usually buy a set of cash cops (opaneks) - such boards , as a rule, 7 cm wide and 2.2 m long. Their color and texture should completely coincide with the color and texture of the door leaf. In order not to wrestle with what to make additional elements, you can buy an additional three cash cops. In fact, special boards are used for this purpose. But they can be much more expensive in price and not in the store. However, this will be the only option if the protruding section of the wall exceeds 7 cm. No matter how hard you try, you will not be able to cut off perfectly like at the factory. All the more, alongside. But the jagged edge is usually hidden. Many door blocks have special grooves for this. If they are not, dobory installed for the riser, after removing the foam in this place. The easiest way to attach additional elements is to use foam. She is filled with the space between them and the cut of the wall, having previously fixed the dobor themselves with adhesive tape. And to avoid cracks, apply spacers - pieces of dry foam or lumps of paper. 3. What to do if the wall does not correspond to the vertical level, or, to put it more simply, is filled up? There are two options: First, cut off the worm or carrot shaped dobor. The main thing - do not forget to leave 5-10 mm for insertion into the groove. Of course, any wedge always catches the eye, and this option is not suitable for everyone. Secondly, you can cut off holes of equal width along the entire length, mount them, and then trim the wall. Perhaps this solution is the best.But if the deviation from the vertical does not exceed 5-10 mm, then you can simply ignore it.
 cashiers of interior doors
door handlers for interior doors
Installing cashiers. Opanelka is a mandatory attribute of the doorway. Many have difficulty articulating the platbands in the corners. Indeed, because they need to gash at an angle of 45 degrees. Professional installer uses a special electric saw - "tortsovochnik". There this function is provided. What to do if there is nothing besides a hacksaw and a square? First, the hacksaw, at a minimum, must be sharp. It is better if it is a spike. Secondly, for zapilivaniya corners, it would be nice to get a casserole. It is cheap. Instead of the flush, in principle, the square will go. If not, and it can be folded diagonally on a sheet of paper, get an angle of 45 degrees. It should be imposed on the opane and spend a pencil. Preliminary it is necessary to make all measurements with the help of a tape measure. interior doors Installation of casters start from the top. This will make it clear whether everything is measured correctly. Many people believe that nails spoil the appearance of the whole structure. However, experts tend to feel free to use them. Of course, nails should be special. Otherwise, you can simply bite off the pliers of the bonnet. In addition, the opallet can be attached to liquid nails or mounting foam. Only fixing can be difficult. Clamps are used for this purpose. Anyway, with a neat attitude, everything will definitely work out.

Related News


Best gifts to a friend by February 14
Do-It-Yourself Postcards by May 9
Summer Landscape
Take Hyundai to lease
Real Doner Kebab
We improve memory available in all ways